Environmental impact assessment

Purpose

Environmental impact assessment (EIA) makes sure decision-makers understand environmental consequences before deciding. It exposes these consequences to scrutiny. This happens before an irreversible decision, not after.

The proponent (the person or entity proposing the activity) usually must gather and disclose likely impacts. Agencies and the public can then comment. The decision-maker must consider this information.

EIA is a process obligation. This means failing to assess properly, or failing to consider the results, can itself ground legal challenge. This is true even if the final outcome was otherwise reasonable.

A sliding scale of assessment intensity

Not every proposal faces the same level of scrutiny. Australian environmental and planning laws generally use a tiered system. Assessment gets more intensive as likely impacts grow in scale and sensitivity.

At the lightest level, a proposal may only need a referral or screening decision. This is a threshold decision by the authority or minister on whether further assessment is needed at all. Many proposals are screened out here because their impacts are not judged significant.

Where impacts are more than minor but not highly significant, a preliminary or documented assessment may be required. This is a more structured report, but still relatively contained.

At the most intensive level, proposals with potentially significant or contested impacts may need a full environmental impact statement (EIS) or public environmental review. This involves detailed technical studies, public exhibition and submissions, and often independent expert review before a final decision.

This graduated structure directs detailed scrutiny toward proposals that actually need it. Minor proposals avoid the lengthy process required for major projects.

Assessment can arise at more than one level

Australia splits environmental approval between state/territory and Commonwealth systems. The same project can trigger separate assessment duties under each. A state or territory statute may require assessment of impacts within that jurisdiction.

Separately, the Commonwealth Environment Protection and Biodiversity Conservation Act 1999 (Cth) applies if a project may significantly impact a matter of national environmental significance. A proponent who thinks it may be a “controlled action” must refer it to the Commonwealth minister, who decides whether Commonwealth assessment is needed and how intensive it should be.

That referral cannot happen while an “alternate pathway” applies. As at 3 October 2026, s 71A (in force since 24 August 2026) bars referral during that time.

The alternate pathways are: a declaration (including in a bilateral agreement) that a class of actions needs no Part 9 approval; an approval under s 146B after a strategic assessment; and bioregional-plan arrangements for restricted or priority actions. Each pathway is conditional, not automatic.

An action named in an exclusion determination falls outside the declaration pathways. So does a larger action where only part is covered by a declaration. A s 146B approval only counts if s 146D(2) applies. The bioregional-plan pathways depend on plan provisions not yet in the Act as compiled on 24 August 2026.

Section 71A was inserted by item 160, Schedule 1 of the Environment Protection Reform Act 2025 (Cth), commenced 24 August 2026 by Proclamation (No. 2) 2026. The bioregional-plan provisions, in Part 12A (inserted by item 323), were not commenced by that Proclamation.

If a referral is made while no pathway applies, it continues even if a pathway later starts to apply, unless withdrawn. But an action named in an exclusion determination under s 36B, or in a bilateral-agreement determination under s 65B, is instead treated as referred under s 68(1) once that determination is made. This rule has applied since 24 August 2026.

Where both state/territory and Commonwealth levels apply, accreditation mechanisms let a single assessment process serve both, avoiding duplication.

What a decision-maker does with an assessment

Finding impacts in an assessment does not force the decision-maker to refuse approval. The assessment informs the decision but does not control it.

Decision-makers usually have broad discretion. They can approve with conditions that avoid, mitigate or offset impacts, refuse approval, or occasionally approve with no conditions at all.

Approval decisions are often challenged later. Common grounds include whether the assessment was adequate, and whether the decision-maker genuinely engaged with it.

Applying this in a problem question

Start by working out which statute applies. There may be state, territory or Commonwealth obligations, so check each level separately.

Next, work out where the proposal fits on the tiered scale. It might need only a screening or referral decision, a documented assessment, or a full environmental impact statement or public environmental review.

Check whether the proposal could be a “controlled action” — this happens if a matter of national environmental significance is affected. If so, a separate Commonwealth referral under the EPBC Act is required, unless an alternate pathway applies.

Keep the assessment process separate from the final approval decision. A flawed assessment is a different legal problem from an unreasonable approval.

Finally, look at what the decision-maker actually did with the assessment. Did they genuinely consider it, impose conditions, or fail to engage with its findings?

A Quick Read uses simpler language and may leave out detail, including whole topics, to stay short. The full article is the complete statement.

Read the full article →

Pop quiz

5 quick questions on this article, the authorities it cites and the articles it links to.

  • About 3 minutes, and no time limit.
  • You can only go forwards: each answer locks when you submit it.
  • After each question you see the right answer, why, and where to read more.
  • Free, and no account needed. Log in or create a free account to keep your scores.